Install guide

Fifteen minutes.
Zero drilling.

Every step, photographed on a real car. HALO’s two wires use the holes your factory badge already has, and it all comes back off if you ever want it to.

~15 minstart to finish
0drilling
2factory pin holes
100%reversible
!
Before you start

Stand behind the car, facing the trunk. “Left” and “right” below are from there. If a camera lens sits inside your roundel’s black ring, stop here: HALO can’t mount there unless the camera is moved.

What you’ll need

Everything’s in the box.
Almost.

In the box
  • 01HALO
  • 0212 V socket adapter
  • 03Long USB-C power cable
From your garage
  • 01Plastic trim tool (never metal)
  • 02Hair dryer
  • 03Isopropyl alcohol and a cloth

No 12 V socket in your trunk? Pick up an add-a-circuit fuse tap, a 5 A fuse and a ring terminal. It’s about $10 at any auto parts store or on Amazon, and the lookup below tells you the exact size for your BMW.

Phase 1

Remove the factory badge.

Prying the factory roundel off with a plastic trim tool
01About 3 minutes

Warm it. Lift it.

Warm the badge with a hair dryer for about 60 seconds. Slide a plastic trim tool under the edge and lift slowly and evenly.

Don’t use a metal tool or pull hard from one side. Both can mark the paint.

Removing the rubber grommets from the badge pin holes
02About 1 minute

Pop out both grommets.

Pull the rubber grommet out of each factory hole and leave both holes open. HALO’s two wires go through them, so there’s nothing to drill.

Cleaning the badge recess
03About 2 minutes

Clean and dry.

Take off any old adhesive, wipe the recess with isopropyl alcohol and let it dry fully. HALO needs a clean, flat surface.

Phase 2

Meet HALO.

HALO box beside the car
04Unbox

Lay everything out.

Set out HALO, the 12 V adapter and the long USB-C power cable. Don’t press HALO onto the car yet.

Lifting HALO out of the box
0530 seconds

Give it a once-over.

Check the screen, the bezel, the mounting surface and both wires before you start.

Right hole · antennaLeft hole · powerBack of HALO showing the taped antenna and the long black power cable
06Important

Know your two wires.

Flip HALO over before routing anything. Each wire has its own job and its own hole.

Short taped wireRight holeThe antenna. Feed it through and leave it inside the trunk. It doesn’t connect to power.
Long black cableLeft holeThe power cable. Feed it through and route it behind the trunk liner.
Phase 3

Wire it and mount it.

Routing the antenna through the right hole and the power cable through the left hole
07About 3 minutes

Feed each wire through.

Antenna through the right hole, left inside the trunk. Power cable through the left hole, then down behind the trunk liner toward power.

Quick check: right = antenna, left = power. Keep both clear of the hinges and anything that moves.

Plugging HALO into the trunk 12 V socket
08About 1 minute

Plug in power.

Trunk has a 12 V socket? Plug in HALO’s adapter and tuck the extra cable behind the liner. That’s it.

No socket? No problem. Use the lookup below to find your BMW. It shows exactly where to tap power and which $10 parts to grab.

Pressing HALO into the badge recess
0930 seconds

Center it. Press it.

Make sure neither wire is pinched, center HALO in the recess, then press firmly and evenly for 30 seconds.

RevMode HALO · power

Power your HALO.

Use the trunk 12V socket whenever your BMW has one. If it doesn’t, open the hardwire lookup for the exact trunk-side parts. They’re about $10 at any auto parts store.

Default installation · use this first

Plug into the trunk 12V socket

No extra power parts are needed. Plug in HALO’s supplied adapter, keep the cable inside the trunk, and hide it behind the trunk liner.

  1. 01Find the trunk 12V socket.
  2. 02Plug in HALO’s supplied adapter.
  3. 03Hide the cable behind the trunk liner.

HALO software · phone setup

Connect. Open. Customize.

Once HALO is powered, connect your phone directly to the emblem and open the RevMode dashboard in your browser.
Connect to HALO Wi-Fi first

The dashboard only connects after your phone joins the Wi-Fi network named HALO.

  1. 01
    Power HALO

    Turn the vehicle’s accessory power on and wait for the HALO display to start.

  2. 02
    Join “HALO” Wi-Fi

    Open your phone’s Wi-Fi settings and connect to the network named HALO.

  3. 03
    Open the dashboard

    After Wi-Fi connects, open Safari or Chrome and go to app.revmode.co.

  4. 04
    Choose your design

    Select or upload an image, video, or GIF, then apply it to the HALO display.

Open the HALO dashboard →

No app download required. Use Safari or Chrome on your phone.

Phase 4

Finish and test.

Closing the trunk with HALO installed
10Close up

Put the liner back.

Tuck the power cable out of sight, check nothing’s pinched, refit the trunk liner and close the trunk.

HALO installed and running
11Done

Final check.

Turn on accessory power and confirm your design is playing. HALO should be centered, the trunk should close normally, and no cable should show.

Going back

Changed your mind? Easy.

Warm HALO, lift it off, unplug it, and press your factory badge back into its original holes with the grommets. No new holes, no marks.

Help

Stuck? We’ve got you.

HALO won’t light up

Turn on accessory power. Check the adapter is seated in the socket, or that your fuse tap is on a circuit that’s live with the car on.

Can’t see HALO’s Wi-Fi

Give it a moment after power-on, stand near the trunk, and look for the network named HALO.

Still stuck

Email a photo of where you are to support@revmode.co. A real person replies, usually within one business day.